Полистал схемы… На вход USB каждый лепит кто во что горазд, хотя стандартная входная развязка на USB, кажется, должна быть всем давно известна — 22Ом резисторы на вход (и, по идее, 47 пик с ног контроллера на землю, то есть если смотреть от разъема, то после входных резисторов). Для того, что бы устройство правильно определялось как high speed, надо бросить резистор 1.5К с ноги контроллера D+ бросить на +3.3В.
Рекомендую все-таки убрать резистор 3К Ом с платы, подтягивающий ногу CLK к земле, и подтянуть каждый переключаемый канал отдельно через свой резистор 3К-5К Ом на землю. В реальных боевых условиях CLK наводится на висящий в воздухе еепром для Saleae, незащищенный от записи, и Suite брикает его. Приходится восстанавливать прошивку. Это недолго, но раздражает. Все то же самое, что ниже, только сдувается резистор с платы, и на нижнюю дорожку (Gnd) припаиваются 2 резистора, ведущие к крайним контактам выключателя.
Выследил поганца. Может кому пригодится:
HKCU\Software\VB and VBA Program Settings\usbeeaxscope\Startup\NumberOfSamples
поменял на значение 1507328 — заработало.
Тут вопрос есть, может кто уже столкнулся… Выставил в Test Pod Oscilloscope размер буфера в 705100K. Не самая лучшая идея, как оказалось.
Сейчас при входе в софтинку тупит долго, потом отваливается с ошибкой. Переустановка софта результата не дала — конфиги не трутся, и непонятно вообще, где эта настройка хранится. Беглый поиск по реестру ничего не дал.
Да у SL бывают приколы но не все так страшно.
Попробуй так:
Лезешь сюда www.rezonit.ru/support/directions/ глядишь как из SL выводить герберы.
Потом качаешь отсюда gerbv.gpleda.org/ программку Gerbv и смотришь полученные герберы.
I am the manufacturer of this XZL-STUDIO AX, and am glad to know this device come to your community. One Russian friend came to my TAOBAO shop and leave some questions about how to use it. Then I think it necessary to explain and advise here.
1) IC U7 is AT24C02. The 7th leg is the WRITE-PROTECTION and soldered to 8th(VCC 3.3V),e.g, this I2C EEPROM can NOT be written by the U6 CY7C68013 any more, in case to prevent the newest version 1.1.73 of U-S-B-E-E SUITE from writing and destroying the VID/PID in U7.
2) 1ACH, 2ACH are analog input, 1DCH-8DCH are digital input.
3) There are 3 potentiometers on the board. RV3 is for zero-level modification, RV2 is for 1ACH amplitude, RV2 is for 2ACH amplitude. You may screw up and down to modify the value. And the calibration function of the software is invalid since the EEPROM can not be written any more.
4) The suite software is better for the logic analyzer function, and if you need to watch the analog signal, use the ax oscilloscope software. AX can only display one analog signal at one time, and you can switch to another signal by clicking CH1/CH2. If you need to watch two signals simultaneously, please choose DX device instead.
5) I will be glad to supply you a suite registration key-gen, but I have no idea how to put it here. Anyone can help me?
Importantly, I do not read in Russian and can only read your web by google-translate, if you have more questions, please write in English and I can understand more clearly.
HKCU\Software\VB and VBA Program Settings\usbeeaxscope\Startup\NumberOfSamples
поменял на значение 1507328 — заработало.
Сейчас при входе в софтинку тупит долго, потом отваливается с ошибкой. Переустановка софта результата не дала — конфиги не трутся, и непонятно вообще, где эта настройка хранится. Беглый поиск по реестру ничего не дал.
Кто сталкивался, куда ковырять?
Попробуй так:
Лезешь сюда www.rezonit.ru/support/directions/ глядишь как из SL выводить герберы.
Потом качаешь отсюда gerbv.gpleda.org/ программку Gerbv и смотришь полученные герберы.
I am the manufacturer of this XZL-STUDIO AX, and am glad to know this device come to your community. One Russian friend came to my TAOBAO shop and leave some questions about how to use it. Then I think it necessary to explain and advise here.
1) IC U7 is AT24C02. The 7th leg is the WRITE-PROTECTION and soldered to 8th(VCC 3.3V),e.g, this I2C EEPROM can NOT be written by the U6 CY7C68013 any more, in case to prevent the newest version 1.1.73 of U-S-B-E-E SUITE from writing and destroying the VID/PID in U7.
2) 1ACH, 2ACH are analog input, 1DCH-8DCH are digital input.
3) There are 3 potentiometers on the board. RV3 is for zero-level modification, RV2 is for 1ACH amplitude, RV2 is for 2ACH amplitude. You may screw up and down to modify the value. And the calibration function of the software is invalid since the EEPROM can not be written any more.
4) The suite software is better for the logic analyzer function, and if you need to watch the analog signal, use the ax oscilloscope software. AX can only display one analog signal at one time, and you can switch to another signal by clicking CH1/CH2. If you need to watch two signals simultaneously, please choose DX device instead.
5) I will be glad to supply you a suite registration key-gen, but I have no idea how to put it here. Anyone can help me?
Importantly, I do not read in Russian and can only read your web by google-translate, if you have more questions, please write in English and I can understand more clearly.
Hope you enjoy it! Thank you!